The new Cloudberry CR-6200 Series is a commercial off the shelf (COTS), fully managed Layer 2/3 Ethernet switch with an embedded Cisco 5921 Embedded Services Router (ESR) IOS and network time server capability (IEEE 1588 PTP, NTP, IRIG, 1PPS), in an ultra-rugged housing. It is specifically designed to provide reliable, high-performance connectivity for extremely demanding size, weight and power (SWaP) constraints in harsh demanding environments (e.g. high altitude, extreme shock & vibration, extended temperatures, humidity, dust & water exposure, noisy EMI, dirty power).
The CR-6200 is an ideal solution for forward-fit and retrofit applications. It provides a technology advantage for deploying data, video and voice services virtually anywhere LAN/WAN connectivity may be required, especially in mobile, airborne, ground, manned or unmanned vehicle and sensor applications. With routing speeds of up to 200 mbps for the Cisco 5921 ESR package or full wire speeds for OnTime Networks' own router package, the unit offers a powerful network solution.
With up to 24 gigabit Ethernet and four 10 gigabit Ethernet ports, the CR-6200 provides a robust network routing architecture with the performance, security, quality of service (QoS), high availability and manageability that customers expect from Cisco IOS-based technologies. The familiar Cisco IOS router software and the Cisco-like CLI interface on the switch management side minimize training requirements and provide extensive support for IPv4/IPv6 routing protocols, IP multicasting, Radio Aware Routing (RAR), Dynamic Link Exchange Protocol (DLEP), remote VoIP, Firewall/IPS/IDS, Mobile Ad Hoc Networking (MANET) and Mobile IP routing for connectivity in Comms on the Move (COTM) applications.
Additional information about the Cisco 5921 Embedded Services Router (ESR) IOS can be found here:
Its modular rugged design, enclosed in a completely sealed housing against dust and water ingress (IP68), requires no active cooling and provides a number of connector options (ceelok FAS-T, MIL-DTL-38999, MightyMouse). The unit features a military-grade power supply for aircraft (MIL-STD-704F) and ground (MIL-STD-1275D) vehicle use, as well as MIL-STD-461F EMI/EMC filtering.
Its performance is optimized for a large numbers of IP-enabled embedded devices, such as computers, cameras, sensors, and command-and-control equipment, deployed in manned and unmanned system platforms at the network edge.
The RCR-6200 supports the latest generation of IPv6 switching, allowing it to meet the most challenging requirements for next generation DoD networks. IPv6 provides improved network security and reliability, while support for more network addresses allows for a greater number of interconnected devices. Additional management and configuration features include quality of service (QoS) prioritization, VLANs, LAG, SNMP, RSTP, VRRP, IGMP and traffic policing, providing customers the flexibility to meet their unique networking requirements.
The CRM6200-MIL is a reliable and accurate PTP Grand Master Clock (GMC) or Transparent Clock/Slave Clock (TC/SC) fulfilling IEEE 1588 STD 2002 (v1) and IEEE 1588 STD 2008 (v2). Both PTPv1 and PTPv2 Slave clocks can co-exist in the same network by using the PTP version translator feature of the CM6200-MIL platform. The switch can also act as a NTP Network Time Server (NTS) and provide GPS emulation output both when enabled as a GMC and when operating as a TC/SC. GPS emulation means Pulse Per Second (PPS) output signals via GPO pins in the power connector (TTL) and NMEA telegrams via RS232 in the same connector. An IRIG-B002 output (TTL) signal can be provided via GPO pins in the power connector.
This fully managed, Layer 2/3 Gigabit switch provides a powerful set of networking features, including support for IPv4 multicast traffic filtering according to static filters or IGMP snooping, Virtual Local Area Networks (VLANs), port control (speed / mode / statistics, flow control), Quality of Service (QoS) traffic prioritization, Link Aggregation (802.3ad), SNMP v1/v2/v3 management, secure authentication (802.1X, ACLs, Web/CLI), redundancy (RSTP/MSTP) and port mirroring.
28VDC redundant power input with polarity protection and power hold-up (option) support is available through the 10 pin power/IO connector. The CR-6200 utilizes for single port connector requirements the Ceelok FAS-T connector for 10/100/1000BASE-T(x) and 10GBASE-T(x) copper ports and the ARINC801 optical termini in circular MIL-DTL-38999 connectors for 1000BASE-X/10GBASE-X fiber ports. For the 28 port variant the 10/100/1000BASE-T(x) ports are provided via D38999 connectors.
The CloudberryMIL CR-6200 Series offers switches with and without time synchronization support for Aerospace and Defense applications.
The new Cloudberry CR-6200 Series is a fully rugged network router, providing extensive support for IPv4/IPv6 routing protocols, IP multicasting, Radio Aware Routing (RAR), Dynamic Link Exchange Protocol (DLEP), remote VoIP, Firewall/IPS/IDS, Mobile Ad Hoc Networking (MANET) and Mobile IP routing for connectivity in Comms on the Move (COTM) applications. Additional information can be found here:
Full wire speeds can be provided with the OnTime Networks' own router package.
|The CR-6200-MIL Series is available as a reliable and accurate (< 20 nanosecond) PTP Grand Master Clock and Transparent/Slave Clock according to IEEE 1588 Std 2002 (PTPv1) or IEEE 1588 Std 2008 (PTPv2) standards, as well as NTP Network Time Server (NTS)|
|The CR-6200-MIL Series with PTP Grand Master Clock capability contains a built-in high accuracy GPS receiver.|
|The CR-6200-MIL Series offers advanced filtering capabilities. Multicast filters can be set on the switch, based on IGMP snooping or by manual configuration of static filters. Layer 4 filtering can be done based on UDP destination or source port numbers of UDP/IP packets.|
|The CR-6200-MIL series is designed for the harsh aircraft and military environment. The platform offers a wide operating temperature range [-40 to +85Cº] with ruggedized military approved connectors. The unit is designed to comply to RTCA DO 160G, and is also designed for MIL-STD 461D, -704E and -810G.|
|The CR-6200-MIL Series supports all relevant IEEE Ethernet standards. Interoperability with other PTP devices is ensured based on extensive testing.|
|The CR-6200-MIL Series offer full management based on HTTP, telnet, CLI or SNMP v1/v2/v3.|
|The CR-6200-MIL Series, with its unique embedded PTP version translator feature, allows Slave Clocks of both PTPv1 and PTPv2 to co-exist in the same network. The need for PTP version translation is driven by the fact that PTPV1 (IEEE 1588 2002) is not backward compatible with PTPv2 (IEEE 1588 2008). Both PTP versions cannot co-exist in the same network unless a PTP version translator is used. OnTime Networks offers a cost efficient solution by introducing a PTP version translation feature into its products which helps to protect your PTPv1 investments. With the embedded PTP version translation you can use your legacy PTPv1 equipment alongside your new PTPv2 equipment without the need to upgrade or change configuration of old PTPv1 equipment.|
|The CR-6200-MIL series offers advanced traffic shaping and quality of service techniques|
|The CR-6200-MIL offers port based VLAN (static) or dynamic VLAN according to IEEE802.1Q are supported.|
The CR-6200-MIL series Gigabit Ethernet Switch offers full wire-speed performance on up to 28 ports
The CR-6200-MIL series supports to Enable/disable ports, MAC based port security, Port based network access control (802.1x), VLAN (802.1Q ) to segregate and secure network traffic, Radius centralized password management and SNMPv3 encrypted authentication and access security
The CR-6200-MIL series offers high performance military style connectors
The CR-6200-MIL Series with Grand Master Clock capability provides GPS emulation (NMEA and PPS 3.3V, 5V or 10V), as well as IRIG-B 002 or IRIG-B 122 outputs.
The CR-6200-MIL Series is ready to be compliant to current integrated Network Enhanced Telemetry (iNET) standards
The CR-6200-MIL series is delivered with detailed application notes as well as specific software.
CloudberryMIL CR-6200 series product comparison chart
|Number of 10/100/1000 BASE-TX||Number of 1000BASE-SX||Number of 10000 BASE-TX||Number of 10000 BASE-SX|
Cloudberry CR-6200 series products
|CR-1608FC4-EPTAP||Managed Industrial Ethernet End-Point Tap (EPTAP) Switch with 4x 10/100/1000BASE-TX (RJ-45) + 4x 1000BASE-X combo ports (SFP fiber ports or 10/100/1000BASE-TX (RJ-45)), with advanced filtering capabilities|
|CR-6212F0-MIL||Managed Ethernet network switch, 12 x 10/100/1000BASE-TX in 12 Ceelok FAS-T connectors|
|CR-6212F0-MIL (10G)||Managed Ethernet network switch, 8 x 10/100/1000BASE-TX in 8 Ceelok FAS-T connectors and 4 x 10000BASE-TX in 4 Ceelok FAS-T connectors|
|CR-6211F1-SX-MIL||Managed Ethernet network switch, 10 x 10/100/1000BASE-TX in 10 Ceelok FAS-T connectors and 1 x 1000BASE-SX in one ARINC 801 D38999 connector|
|CR-6212F2-SX-MIL||Managed Ethernet network switch, 10 x 10/100/1000BASE-TX in 10 Ceelok FAS-T connectors and 2 x 1000BASE-SX in two ARINC 801 D38999 connector|
|CR-6212F4-SX-MIL||Managed Ethernet network switch, 8 x 10/100/1000BASE-TX in 8 Ceelok FAST connectors and 4 x 1000BASE-SX in four ARINC 801 D38999 connector|
|CR-6224F0- MIL||Managed Ethernet network switch, 24 x 10/100/1000BASE-TX in 2 38999 connectors|
|CR-6228F4-SX-MIL||Managed Ethernet network switch, 24 x 10/100/1000BASE-TX in 2 38999 connectors and 4 x 10000BASE-SX in four ARINC 801 D38999 connector|